Chino QY-DC-006 Introduction: What is the cooker? Induction cookers, also known, is a product of modern kitchen revolution, it requires no flame or heat conduction and let the heat generated directly in the bottom of the pot, so the thermal efficiency has been greatly improved. Kitchenware is an energy efficient, completely different from the traditional all fire or no fire conduction heating kitchenware. Cooker is made of the principle of electromagnetic induction heating electrical cooking appliances. By high-frequency induction heating coil (i.e., excitation coil), a high-frequency power conversion device, the controller and the cooker pot ferromagnetic material and other components. When used, the heating coil an alternating current is passed through the coil around it generates an alternating magnetic field, alternating magnetic field of magnetic field lines by most metal pot, a large amount of eddy currents in the bottom of the pot, and thereby generate heat required for cooking. No fire during heating, security and health. Here I will introduce Chino QY-DC-006, this cooker: Chapter product structure and characteristics of a product structure Second, the product features a chapter to use, choose safe power: Choose a safe supply of household appliances is very important, not only a cooker, any appliance should be noted that, in particular, high-power appliances such as cooker, its supply high security requirements. Therefore, the power of choice in what I should choose more than 15A power supply for the cooker, but the best. 2, keeping the appliance intake and exhaust smooth: As heated kitchen appliances, heating up at work is a normal phenomenon, pay attention cooker air intake vents are not obstructed, intake and exhaust smoothly without retention, it is safe to use important safeguard. In addition, once found cooker fan fails, stop turning it should quickly turn off the power, so that the natural cooling evacuation service station to check the cause and thoroughly repaired again be put into use. 3, placed parallel to avoid tilt: Cooker placement is very important when using the cooker should be placed on a horizontal table operation, so not only because of the slope of the cooker to avoid causing overturning phenomenon, but also to maintain the cooker is not due to deformation and shun bad . 4, regular cleaning: After using the appliance for some time to regularly clean, cleaning is to extend the useful life of one of its most important method. You should use a soft cloth and a soft brush with alkaline cleaner for cleaning, avoid the use of steel balls and other hard objects to clean the surface of the cooker to avoid surface damage. 5, the use of specialized cookware: generally have a special pot cooker, electronic oven has a special pot cooker pot with a dedicated electronic furnace itself has a protective effect, so try to choose to cooperate with a special pot cooker cooker is a wise use approach. In addition, the cooker is a certain limit load, too much weight can cause damage, please read the instructions in the provisions relating to "load limit" of. 6, pregnant women should not use the appliance to work when there is radiation, so pregnant women should not use the appliance. Third, the special key operation described in Chapter III safety precautions when using the installation and operation of a cooking stove, must take the following safety measures. 1. Before you can use - before using View stove surface cracks or damage, such as damaged, do not use. - When the power cord is damaged, do not use. - Whether any form of damage stoves, please do not attempt to repair stove. - Keep away from water and heat, and to ensure adequate space for cooking stoves. - Use appropriate stainless steel cookware, pots and pans should not put before the connection or turn on the power. - Cooking stoves for household use only, not for commercial purposes. - Do not touch the plug with wet hands. 2. Installation and Connections - Do not share the same with other high-power electrical outlet. - All tests should be done by a qualified technician, and in strict accordance with local safety regulations installation. - Appliances must be connected to a suitable power source is connected, it should be in accordance with local installation wiring, grounding and safety regulations. Manufacturers due to incorrect installation will cause damage to the stove does not assume any responsibility, for example due to a lack of or insufficient effective grounding system or click on a result of improper installation caused. - Do not connect the power supply through the drain Sue. Pai Su can not achieve the required security guarantees protection equipment, such as the prevention of overheating. - The product should be qualified by an isolation device or bipolar and fused switch box (the switch box must comply with local regulations) to connect. - Stoves can be installed on top of a dishwasher, washing machine, dryer or double-door refrigerator. Because it comes out of the high heat will damage. Bad other electronic devices below, thereby damaging the stove ventilation system. - In just installed a few days, may appear on the edge of the glass ceramic gap, but it will be with the use of cooking stoves reduce, and will not affect the electrical safety of the device. 3. Protection appliances from damage - Do not throw anything into the ceramic surface, even a small and light objects can also cause a click or on a certain degree of damage to the equipment. If the ceramic surface cracked, immediately turn off the stove, turn off the power engine, and then contact your local qualified service technician. - Make sure the same period of time, only one control button is pressed. Do not let the heat of objects in contact with the control key, because doing so would make the cooker error response. - Do not insert metal objects such as knives, forks, spoons ,, lids, cans or aluminum foil on the oven surface, because they absorb heat gain on the ceramic surface. - Do not put any paper in between the stove and the stove ceramic panel, because the paper is likely to be ignited. - Do not heat the empty stove or make it overheat. - Do not heat the stove near the control area, because they will damage the electronic components of the control zone. - Do not block the air intake and outlet, because this will cause the temperature to rise back box. At this overheating protection function will start, let stove automatically stop working. - If there is a drawer located beneath stoves, should ensure that there was enough space between the bottom of the wrapped object and electromagnetic cooking stoves drawer to ensure adequately ventilated cooking stoves. - If the user is more sensitive to smell, when using the cooker should maintain good ventilation. 4. Protect stove, to prevent it from fire - can only be done using the flat cooking stoves (refer to Chapter 2, "applicable stoves"). Otherwise, the temperature sensing cooking stoves may malfunction, causing overheating or fire. - Cooking stove, where applicable, its surface temperature is; and after open out equipment or an open stove, its surface remains hot for some time. This makes it before the remaining heat dissipation, there are still likely to be too hot, it should let their kids away from the device. - After the stove to cool down before cleaning them. - Should stoves reach of small children, and the panhandle place away from the edge of the pot ring and inwards. - When cooking with fat or oil. Never relax Hai pot custody. Very hot oil can cause fire, causing damage to other electronic devices. In the process of heating the fat should be heated slowly and observe. - Do not store anything that might lead to interest children in or near stoves, otherwise, have the opportunity to entice children to climb the risk of being burned on the stove. - In case of oil or fat fire, do not use water to fire, you should use a suitable fire blanket or fire extinguisher. - Do not try to heat unopened canned food, because pressure can build up and cause an explosion in the tank, causing bodily harm and burns. - Should immediately cut off the power supply after use, the internal fan to help cool the furnace body and the furnace surface. Chapter IV Care and Maintenance ceramic plate is easy to clean up. If it is minor dirt, wipe with a soft, damp cloth. If the oil dirt, stick with a soft damp cloth to wipe a small amount of toothpaste or neutral detergent when the appliance is hot, hot this time carefully, and then wipe with a soft damp cloth to leave no residue. Housing is generally neutral detergent to clean it. Each time you use the pot to keep clean, not dry, use toothpaste or detergent to clean when the grain discoloration. Need to wait for the fan shutdown completely stopped before disconnecting power. How to clean the fan to fan grille, scrub with a soft brush;? For the fans relate to disassemble the internal cleaning; if you need it, I suggest you go to our after-sales outlets, by our professional maintenance staff you clean; but the most important thing is to maintain a good working environment. Pot at home may not be available? Induction heating principle is rather special, is the electromagnetic induction heating, it must be magnetically permeable material, such as iron, stainless steel. Specially adapted best to use pots and pans, as a substitute for other performance may be affected. 304 and 430 stainless steel iron are usually related to the distribution of cookware manufacturers use quality than ordinary pots and pans a lot of good, it is recommended to use special pots and pans. Splashed water how to do? As long as water vapor or water droplets on the surface of the cooker, but then does not flow inside the appliance (generally within the water will not flow into the machine), does not affect the normal operation of the appliance, can be assured. Panel yellow how to do to keep the pot clean, not dry when used every time, use toothpaste or detergent scrub when discoloration;? Also, do not pad things like newspaper on the panel. Chapter failure analysis and solutions not boot (press the power button LED is not lit) (1) Check and replace bad button keypad (2) Power Cables loose reconnection (3) power line is not energized or reconnection new ones (4) Replace the fuse (5) power transistor IGBT bad replacement (6) bad resonance capacitor C103 replacement (7) the damping diode check and replace (8) transformer bad, no 18V output Inspect and replace (9) circuit board assembly to replace a bad set pan, indicator light, but not heat (1) did not lock the reel lock reel (2) Zener diode Zener diode ZD101 bad-for-ZD101 (3) substrate components bad light does not change the base plate assembly The fan rotation (1) LED slot re-plug or plug wire adverse change LED board (2) Zener diode Zener diode ZD2 bad change ZD2 (3) substrate components bad-for-substrate assembly is heated, but the light does not shine (1 ) LED diode LED diode bad change (2) LED board assembly to change the LED board assembly is not bad pot set, indicator light, no heat (1) thermistor re-plug wires loose or damaged components or replace thermistor (2) manifold or manifold TA8316 bad bad LM339 LM339 change or TA8316 (3) transformer plug bad check or change the master IC (4) of the substrate components bad exchange board assembly power change (1) adjustable resistance adjustable resistance to change (2 ) Heating / fixed temperature resistance wrong or short check heating / fixed temperature resistance (3) control IC bad check or change the master IC (4) substrates or substrate components bad exchange swap buzzer sounding board assembly (1) thermal switch bad / thermistor bad, bad-for-master IC / thermal switch / thermistor / Master IC (2) Resonators bad, [1] to change the oscillation transformer bad child, check or replace the transformer (3) substrate components bad checks or Replace the circuit board assembly cookware properly, but blink and issued a "ding" sound (1) cookware is detected at the critical point (2) replace the R104 resistance pot set, lights flashing (1) CT worse than the current ratio of current transducer CT (2) pans right, non-adjustable resistor pot with a bad check or reflect corresponding devices can not operate without electricity (1) plug and socket connection is bad or too loose plug or inside with the right pots and pans (3) IC1 / IC6 / R501 No metal contact (2) the magnetic plug furnace good (3) no 220V power outlet (other appliances can not be switched on at the socket) to replace the socket on the power on